HOME > MAGNETIZER> Magnetizer / voltage capacitor type

MAGNETIZER

MAGNETIZER
  • OUTLINE
  • LINEUP
DEMAGNETIZER
  • OUTLINE
  • LINEUP
MAGNETIC PARTICLE EQUIPMENT
  • OUTLINE
  • LINEUP
MAGNETIC MEASURING INSTRUMENT
  • LINEUP

Magnetizer Magnetizer<High voltage capacitor type>

Multifunctional energy-saving type. High voltage oil filled capacitor type magnetizer.

Eco-Mag SX-E Japanese patent No.4554346

Eco-Mag SX-E
Control

Digital control unit CU-2

Strengths

The new controlled charging system with a three-phase power supply reduces power consumption and enables high-speed charging. In addition, our exclusive patented "regenerative function" realizes further energy saving.

Application

Multi-pole magnetization of rare earth magnets, magnetization of large block magnets, magnetization of large servo motors, rare earth PM-type multi-pole stepping motors, rare earth spindle motors, VCMs, pickups

Rated Value
  • Charge voltage: 1500(V) to 2500(V)...in 500(V) increments
  • Capacitance: 200 (µF) to 2000 (µF)...in 200 (µF) increments
  • Maximum allowance current: 30 (kA)
Standard Specifications

SX-E2520 Eco-Mag

  • Charge voltage：100～2500（V）
  • Capacitance: 2000 (µF) with capacitance toggle
  • Charging time: 5 sec.
  • Maximum allowance current: 30 (kA)

controller

Mounted on SX and Eco-Mag SX-E type magnetizers

Magnetizer digital control unitCU-2

CU-2

Explanation of Operation Panel
  1. Condition setting channel (with 10-channel memory function)
  2. Output selection switch (optional)
  3. Magnetizing/demagnetizing switch (option)
  4. Charge voltage setting value (in 1V increments) / High limit / Low limit
  5. Charge voltmeter
  6. Charge voltage judgment display LO-GO-HI
  7. Charge level display
  8. Current standard value (in 0.01kA increments)/ High limit / Low limit
  9. Discharge ammeter
  10. Discharge current judgment display LO-GO-HI
  11. Repeat charge switch (recharge after discharge)
  12. Shot charge switch (charge once with switch ON)
  13. Trouble reset switch
  14. Discharge switch
  15. External operation display (when controlled by an external device)
  16. Data setting switch
Strengths

Energy-saving, high-performance control unit enabling high-speed charging with three-phase power supply

Compared to the single-phase power supply conventional type, the use of a three-phase power supply stabilizes the power line and saves energy. High-speed charging is realized with less power consumption.

Greatly enhanced based on the CU-1 model! Correspond to external interface "RS-232C".

Enhanced functionality over previous model to allow support of an external "RS-232C" interface (optional). Also capable of sending pass/fail signals for charge voltage and discharge current values during magnetization. Connecting to our "Data Acquisition System" will make it easier a fully numerically controlled as magnetizing conditions

Realizing high-speed charging and stable charge voltage with 80KHz inverter control.

Main options for the CU-2 control unit

(1) External control options

  1. Recall channels
    (Channel could be set with BCD code using PLC, etc.)
  2. Commanding charging initiation
  3. Choose Magnetization / Demagnetization

(2) 「RS-232C」 communication

  1. Charge voltage comparator signal output HI/GO/LO
  2. Discharge current comparator signal output HI/GO/LO
  3. Charge voltage value at discharge
  4. Discharge current value

● Digital control unit CU-2 can also be mounted on both magnetizer and demagnetizer.

PAGE TOP